Guitar Cab Which Speaker Output Should I Use

Posted November 14 2017. OK so in your case here you should be able to use both cabs together.

Best 2x12 Cabinet Configuration Gearslutz Com Bass Amps Mailbox Design Guitar Cabinet

Guitar amps are specifically designed to output the frequencies an electric guitar produces.

. 8ohms felt closer to the 16ohm cabs than the 4ohm. It doesnt matter at this stage that PA speakers have a flat response because guitar speakers have already shaped the sonic character. Short and sweet - 4ohm configurations seemed to provide more clean volume which is how I wire my PA speakers 16ohm provided more breakup and smoother distortion while allowing me to drive the amp harder with less resulting volume.

Do some research on 4 cable method with Helix and also wetdrywet methods 4 cable method with a guitar amp AND two FRFR speakers 2. Just wondering how I can get a general idea of how a speaker might sound based off the specs. Its perfectly okay to mix two speakers of differing power ratings.

But in general youd have better luck with a bass than an electric guitar through any PA speaker. A 4x12 cab is typically 16 ohms so when you connect two of them together in parallel the total load becomes 8 ohms. You can do either or both.

Im still confused been in the combo amp world for too longi use em for guitar but on bass we have a 400 watt amp head at 4 ohms or 8 ohms has the option and a 410 cab thats at 4 ohms at 1000 watts. Hope this helps some more. That cab can either be wired to have a 4ohm in parallel and a 16ohm in.

The 4x12 cabinet is sometimes referred to as a half-stack and players routinely connect two of them to a single amp to create a full stack. It depends on the speakers impedances. In a performance situation a guitar amp combo or cabinet can be miked and feed into a venue back line audio PA system.

Most amplifiers on the planet can run an 8. That can potentially your output transformer or a fuse if your amps smart. Using the Thiele Small parameters of a typical guitar speaker you will find that halving or doubling the cabinet size makes minimal difference to the response.

If you are using two identical cabs for example two 16 ohm Marshall 1960 cabs then you will need to halve the output impedance of your head to 8 ohms in this caseCabinet wiring schemes vary so if you are swapping speakers always match the impedance of the speaker you are replacing to that of the one you are removing and never alter the wiring. In short yes you can use a guitar amp as a speaker to listen to music. Despite all the doom-speakers and nay sayers this CAN NOT and WILL NOT damage an amp.

If its a mono cab the 2 jacks would typically be wired in parallel and in that scenario you should only use one amp at a time plugged into either jack. Guitar speakers become non linear at very low levels compared to other types of speaker greatly reducing the significance of Thiele Small parameters in actual speaker use. You always want to match your amp ohms to the speaker ohms or keep your amps ohm output at a lower setting than the ohm of your speakers.

The amp head should power the cab right. I know that its a sum of all parts cable cab design and wood etc. If you use a stereo cab to produce guitar amp output it will lack this final tone shaping.

You may get a good result with a bass but most bass players like the punch of 10s and only use larger woofers when combined with 10s or something of similar size. Theres a reason guitar cabs dont have 18 inch speakers in them. If you do this then the overall cabinet rating will be twice the lowest rated value.

Granted there will be some differences in the recorded sound between what the guitarist hears and what the mic hears but it will be much closer than what comes from the line output. 1 Image courtesy of Weber Speakers. This isnt to say that you should never use the.

So just use the 4-ohm output on the back of the head and youre good. Similarly a 2x12 cab with dual 60-watt speakers provides you 120 watts to play with which is still great. So a 2x12 cab loaded with both a 25- and a 60-watt speaker will have an overall power rating of 50 watts.

The speaker is as much a part of the instrument as the belly of a violin to which which it is exactly analogous. If you have an 8-ohm speaker and your amp is set at 4 ohms youll be okay since your 8-ohm speaker would be able to handle the weaker signal from the amp. Through my head 6505 two parallel outputs I have to configure it on 8 Ohms to send out 2 cables output to the 2 inputs of my 212.

Wont light up on fire or start clipping. However by looking at specs and looking at voice coil and resonant frequency and all. However none of your presets created using headphones will sound the same through speakers and especially through a guitar amp.

For low power 10 to 20 watts tops you will be fine. Using both jacks with 2 amps into a mono cab will likely destroy one. I use the cab sim on the main outputs but turne it of for monitor becourse thats were I use the Bogner cab.

Therefore using one to play a podcast or an album might mean trouble for the amps internals especially if the music is. From an engineering standpoint the only thing wrong with using guitar cables for speakers is that the wire is too small and the power loss and resultant cable heating will be substantial. Should it be better to put two frfr speakers in my Bogner cab or will the guitar cab still not be totaly neutral becourse its still a guitar cab after changing the celestion vintage 30s with full range 12 inch speakers.

However there are a few risks associated with doing so. With a 16-ohm cab and an 8-ohm cab together in parallel you have a total of 5333 ohms. I bought a PPC 212 orange cab that has two parallel inputs some versions of it are 1 input and 1 link cable which is an output.

Line 6 1x12 Speaker Systems Impulse Response Guitar Cabinet